EP1K30QC208-2N

EP1K30QC208-2N FPGAs Overview

Features

■ Programmable logic devices (PLDs), providing low cost system-on-a-programmable-chip (SOPC) integration in a single device – Enhanced embedded array for implementing megafunctions such as efficient memory and specialized logic functions – Dual-port capability with up to 16-bit width per embedded array block (EAB) – Logic array for general logic functions 

■ High density – 10,000 to 100,000 typical gates (see Table 1) – Up to 49,152 RAM bits (4,096 bits per EAB, all of which can be used without reducing logic capacity) 

■ Cost-efficient programmable architecture for high-volume applications – Cost-optimized process – Low cost solution for high-performance communications applications 

■ System-level features – MultiVoltTM I/O pins can drive or be driven by 2.5-V, 3.3-V, or 5.0-V devices – Low power consumption – Bidirectional I/O performance (setup time [tSU] and clock-tooutput delay [tCO]) up to 250 MHz – Fully compliant with the peripheral component interconnect Special Interest Group (PCI SIG) PCI Local Bus Specification, Revision 2.2 for 3.3-V operation at 33 MHz or 66 MHz 

■ Extended temperature range

General Description

Altera® ACEX 1K devices provide a die-efficient, low-cost architecture by combining look-up table (LUT) architecture with EABs. LUT-based logic provides optimized performance and efficiency for data-path, register intensive, mathematical, or digital signal processing (DSP) designs, while EABs implement RAM, ROM, dual-port RAM, or first-in first-out (FIFO) functions. These elements make ACEX 1K suitable for complex logic functions and memory functions such as digital signal processing, wide data-path manipulation, data transformation and microcontrollers, as required in high-performance communications applications. Based on reconfigurable CMOS SRAM elements, the ACEX 1K architecture incorporates all features necessary to implement common gate array megafunctions, along with a high pin count to enable an effective interface with system components. The advanced process and the low voltage requirement of the 2.5-V core allow ACEX 1K devices to meet the requirements of low-cost, high-volume applications ranging from DSL modems to low-cost switches.

The ability to reconfigure ACEX 1K devices enables complete testing prior to shipment and allows the designer to focus on simulation and design verification. ACEX 1K device reconfigurability eliminates inventory management for gate array designs and test vector generation for fault coverage.

Table 4 shows ACEX 1K device performance for some common designs. All performance results were obtained with Synopsys DesignWare or LPM functions. Special design techniques are not required to implement the applications; the designer simply infers or instantiates a function in a Verilog HDL, VHDL, Altera Hardware Description Language (AHDL), or schematic design file

The INTEL Embedded - FPGAs (Field Programmable Gate Array) series EP1K30QC208-2N is FPGA ACEX 1K Family 30K Gates 1728 Cells 200MHz CMOS Technology 2.5V 208Pin PQFP, View Substitutes & Alternatives along with datasheets, stock, pricing from Authorized Distributors at bitfoic.com, and you can also search for other FPGAs products.

Features

■ Programmable logic devices (PLDs), providing low cost system-on-a-programmable-chip (SOPC) integration in a single device

– Enhanced embedded array for implementing megafunctions such as efficient memory and specialized logic functions

– Dual-port capability with up to 16-bit width per embedded array block (EAB)

– Logic array for general logic functions

■ High density

– 10,000 to 100,000 typical gates (see Table 1)

– Up to 49,152 RAM bits (4,096 bits per EAB, all of which can be used without reducing logic capacity)

■ Cost-efficient programmable architecture for high-volume applications

– Cost-optimized process

– Low cost solution for high-performance communications applications