EP2C5T144I8N

EP2C5T144I8N FPGAs Overview

Introduction

Following the immensely successful first-generation Cyclone® device family, Altera® Cyclone II FPGAs extend the low-cost FPGA density range to 68,416 logic elements (LEs) and provide up to 622 usable I/O pins and up to 1.1 Mbits of embedded memory. Cyclone II FPGAs are manufactured on 300-mm wafers using TSMC's 90-nm low-k dielectric process to ensure rapid availability and low cost. By minimizing silicon area, Cyclone II devices can support complex digital systems on a single chip at a cost that rivals that of ASICs. Unlike other FPGA vendors who compromise power consumption and performance for low-cost, Altera’s latest generation of low-cost FPGAs—Cyclone II FPGAs, offer 60% higher performance and half the power consumption of competing 90-nm FPGAs. The low cost and optimized feature set of Cyclone II FPGAs make them ideal solutions for a wide array of automotive, consumer, communications, video processing, test and measurement, and other end-market solutions. Reference designs, system diagrams, and IP, found at www.altera.com, are available to help you rapidly develop complete end-market solutions using Cyclone II FPGAs.

Features

■ High-density architecture with 4,608 to 68,416 LEs 

● M4K embedded memory blocks 

● Up to 1.1 Mbits of RAM available without reducing available logic 

● 4,096 memory bits per block (4,608 bits per block including 512 parity bits) 

● Variable port configurations of ×1, ×2, ×4, ×8, ×9, ×16, ×18, ×32, and ×36 

● True dual-port (one read and one write, two reads, or two writes) operation for ×1, ×2, ×4, ×8, ×9, ×16, and ×18 modes 

● Byte enables for data input masking during writes 

● Up to 260-MHz operation 

■ Embedded multipliers 

● Up to 150 18- × 18-bit multipliers are each configurable as two independent 9- × 9-bit multipliers with up to 250-MHz performance 

● Optional input and output registers 

■ Advanced I/O support 

● High-speed differential I/O standard support, including LVDS, RSDS, mini-LVDS, LVPECL, differential HSTL, and differential SSTL 

● Single-ended I/O standard support, including 2.5-V and 1.8-V, SSTL class I and II, 1.8-V and 1.5-V HSTL class I and II, 3.3-V PCI and PCI-X 1.0, 3.3-, 2.5-, 1.8-, and 1.5-V LVCMOS, and 3.3-, 2.5-, and 1.8-V LVTTL 

● Peripheral Component Interconnect Special Interest Group (PCI SIG) PCI Local Bus Specification, Revision 3.0 compliance for 3.3-V operation at 33 or 66 MHz for 32- or 64-bit interfaces 

● PCI Express with an external TI PHY and an Altera PCI Express ×1 Megacore® function

● 133-MHz PCI-X 1.0 specification compatibility 

● High-speed external memory support, including DDR, DDR2, and SDR SDRAM, and QDRII SRAM supported by drop in Altera IP MegaCore functions for ease of use 

● Three dedicated registers per I/O element (IOE): one input register, one output register, and one output-enable register 

● Programmable bus-hold feature 

● Programmable output drive strength feature 

● Programmable delays from the pin to the IOE or logic array 

● I/O bank grouping for unique VCCIO and/or VREF bank settings 

● MultiVolt™ I/O standard support for 1.5-, 1.8-, 2.5-, and 3.3-interfaces 

● Hot-socketing operation support 

● Tri-state with weak pull-up on I/O pins before and during configuration 

● Programmable open-drain outputs 

● Series on-chip termination support 

■ Flexible clock management circuitry 

● Hierarchical clock network for up to 402.5-MHz performance 

● Up to four PLLs per device provide clock multiplication and division, phase shifting, programmable duty cycle, and external clock outputs, allowing system-level clock management and skew control 

● Up to 16 global clock lines in the global clock network that drive throughout the entire device 

■ Device configuration 

● Fast serial configuration allows configuration times less than 100 ms 

● Decompression feature allows for smaller programming file storage and faster configuration times 

● Supports multiple configuration modes: active serial, passive serial, and JTAG-based configuration 

● Supports configuration through low-cost serial configuration devices 

● Device configuration supports multiple voltages (either 3.3, 2.5, or 1.8 V) 

■ Intellectual property 

● Altera megafunction and Altera MegaCore function support, and Altera Megafunctions Partners Program (AMPPSM) megafunction support, for a wide range of embedded processors, on-chip and off-chip interfaces, peripheral functions, DSP functions, and communications functions and protocols. Visit the Altera IPMegaStore at www.altera.com to download IP MegaCore functions. 

● Nios II Embedded Processor support

The INTEL Embedded - FPGAs (Field Programmable Gate Array) series EP2C5T144I8N is FPGA Cyclone II Family 4608 Cells 402.58MHz 90nm Technology 1.2V 144-Pin TQFP, View Substitutes & Alternatives along with datasheets, stock, pricing from Authorized Distributors at bitfoic.com, and you can also search for other FPGAs products.

Features

The Cyclone II device family offers the following features:

■ High-density architecture with 4,608 to 68,416 LEs

● M4K embedded memory blocks

● Up to 1.1 Mbits of RAM available without reducing available logic

● 4,096 memory bits per block (4,608 bits per block including 512 parity bits)

● Variable port configurations of ×1, ×2, ×4, ×8, ×9, ×16, ×18, ×32, and ×36

● True dual-port (one read and one write, two reads, or two writes) operation for ×1, ×2, ×4, ×8, ×9, ×16, and ×18 modes

● Byte enables for data input masking during writes

● Up to 260-MHz operation

■ Embedded multipliers

● Up to 150 18- × 18-bit multipliers are each configurable as two independent 9- × 9-bit multipliers with up to 250-MHz performance

● Optional input and output registers